Category: Cleveland Browns Fan Shop

Hand Crank Shortwave Radio

Share Button

You need to own a hand crank short wave radio. While these shortwave radios may seem to some like novelties, they can save your life in an emergency. A shortwave radio isn’t just some AM/FM radio, it picks up a variety of shortwave radio signals. These can include but aren’t limited to weather stations, news broad casts, and even signals from other parts of the country and the world. While you may not think of these as important, in an emergency, these radios and stations can be your only link to the outside world.

A hand crank short wave radio has many different power options today. What the hand crank does is every time you turn the crank, the mechanical energy is instantly turned into electrical energy, enough to power the radio itself, and even to charge up the rechargeable batteries. Because the cranking technology has improved so much over the last few decades, turning the crank just a few minutes can power the radio continuously for more than two hours without interruption. They can also use batteries, and when there is power, plugged into the wall outlets.

The real purpose of a hand crank shortwave radio is for if you are stranded, whether on land or at sea, or if you are in the middle of some kind of natural or man made disaster. No matter what the situation, chances are there isn’t going to be any electrical power, and any kind of regular electronic device isn’t going to work. This is where the hand crank action comes into play. In many cases, evacuation procedures are going to be announced over short wave radios from emergency services. They may tell you that help is on the way, where to go, and even what to do until help arrives. In the case of flooding, storms, or tornadoes there can be more important information given on how long the storm is going to last, or how much more inclement weather is on the way. Without this vital information, you could be headed for an even more dangerous situation, or even stranded for longer, because you didn’t know where to go or what to do.

It is important that you keep a hand crank shortwave radio in many different places. You should have shortwave radios in your home, vehicle, and if you own an RV or a boat, you should have one in these as well. You just never know where an emergency will strike, and having one at home while you are stranded in the middle of nowhere doesn’t do you any good.

Just as a hand crank shortwave radio can save your life, you also have to buy the right shortwave radios as well. There are many different brands and models of these radios, and they come in a varying prices. While there many different models, not all of them are the same. The first thing you need to think about when choosing one of these radios is what your needs are. If you just want one to listen to music on the go without having to lug around a bunch of batteries, then cheaper models are a decent choice. One of these is the Eton FR 150. This radio is small and compact, and has very minimal options. Because of this, the cost is quite low.

For hand crank shortwave radio options, where you need access to multiples channels, and emergency bands, more expensive shortwave radios are a better option. This is because they have a better quality sound, and are able to pull in more channels and stations. They have better batteries, and their cranking mechanisms last far longer than cheaper models. Even so, a good radio shouldn’t cost you more than fifty to a hundred dollars.



Source by Nicole Roberts

Share Button

How To Develop A Relationship With Your Stepkids

Share Button

After a night of Las Vegas debauchery, a man groggily wakes up to find a scantily dressed woman next to him in bed. On the nightstand, he sees what appears to be a wedding photo from one of the strip's wedding chapels. Hastily putting on his glasses he covers his mouth in shock as he realizes he's the one in the picture.

Although the woman's face is partly covered, he notices the cheap wedding ring on her finger. He spots an open purse. He rummages through her handbag and he finds her wallet. He looks at her driver's license and sees her first name is Christina – he already knows what her last name is.

And before he closes her bag he finds a wide-ruled paper written in crayon beginning with Dear Mommy. The now-sober man realizes not only is he a new husband, but he is also a new stepdad.

How To Do It

When a couple dates, they make a connection and fall in love before deciding to get married. In the same way, if there's a child involved and your relationship is heading towards the altar you should begin courting your future stepchild. With the purpose of establishing a connection and developing a relationship before proposing marriage.

Developing a relationship with a potential stepchild is much easier and less stressful for all concerned when a partner is still considered to be a parent's boyfriend or girlfriend than it is when you become a stepparent. If you already have children your partner needs to understand and be able to embrace the fact, you come as a package deal.

Do not Be Santa

A common mistake made by many stepparents-to-be is to shower their fiancé's children with gifts in an attempt to buy their affections. The first issue is kids know when someone is trying to buy their love. They're savvy enough to not fall for the bait.

The second issue is the child might start to expect gifts from you all the time and without you're Daddy Warbucks, this will ever put a strain on your finances. Or even worse you contribute to the creation of a spoiled brat that expects to receive everything they want.

In the end, you run the risk of not achieving your desired results and your stepchild-to-be might become resentful of your attempt to bribe them for their love. The affection and trust of a stepchild come with taking the time and effort to develop a real relationship with them – not from trying to push it onto them.

Take an Interest in Your Child

One of the best ways to connect with a new stepchild is to take an interest in what interests them. If a child is not open about what they like, a talk with the biological parent might provide a starting point. If a stepchild is interested in animals, a trip to the zoo may provide a nice opportunity for bonding.

Older children can be harder to pin down and there are fewer opportunities to bond with them. Offering to help with homework or taking an interest in their favorite video game may not be the strongest of beginnings to a relationship, but it is a beginning.

Involve the Child in Your Interests

While you're taking an interest in your future stepchild's interests, you can also involve your stepchild in your interests. A child already knows their biological parents and has had plenty of opportunities to get involved with them and their interests. One of the easiest ways to let a new stepchild into the life of their new or potential stepparent is to let them get involved in their interests.

For example, if the stepmom-to-be is part of a bowling league, the kids may not mind going down to the bowling alley and get to watch or even take part in the game. At the same time, it's important to make sure the stepchild gets to spend time with their biological parent. This is especially true for children in a shared customs situation.

In shared custody, your stepchildren will only get a limited amount of time to spend with each of their biological parents. You should help make sure your stepchild maintains a healthy relationship with their biological mother and father.

Take Your Time

The greatest gift you can give your new stepchild is time. Remember your stepchild is grieving the loss of their nuclear family. It will take time for them to get used to the fact that their biological parents are no longer living in the same home.

It may take even more time for them to accept one or both of their parents have found someone else to fall in love with. It will take at least a couple years before a stepparent can actually build what could have considered a healthy relationship with their stepchildren. This can be made easier if the future stepparent begins to connect with the child before the wedding.



Source by Gerardo Campbell

Share Button

6 Fat Burning Exercises When the Weather Isn’t Co-Operating

Share Button

We all know this scenario, you are totally focused on your weight loss goal, you have your gear, you’ve done your stretches and then it starts to rain! So what do you do? After all you have committed yourself to leading a healthier lifestyle and can’t quit now. Thankfully there are ways to burn fat indoors.

Every day with, with every action you get a little bit closer to achieving your weight loss goal. Just because the weather isn’t very accommodating doesn’t mean that you can give up just yet! Indoor exercise may not always be comfortable, but it is practical when you don’t want to give up on a goal.

After all, if you have a real weight goal, no excuse is going to get in your way even if the weather isn’t playing fair.

TV exercise

Let’s face it, people spent a lot of time in front of the TV. I know because I was one of those people! Try increasing your efficiency and kill two birds with one stone by getting your fat burning exercise done while watching your favourite TV programs. You can even play a dedicate exercise DVD.

Window shopping

Did you know that walking is one of the best forms of exercise? And that is simply because it doesn’t put as much strain on the body as traditional forms of exercise. So when the weather outside is nasty, take a stroll through the mall and do a bit of window shopping. You can even get your friends involved by starting a ‘mall walking club’.

Dancing

As long as you are going to be moving anyway you might as well be learning a new skill, like dancing. There are many different types of dancing; all of them are effective in burning fat. Even the slowest types of ball room dancing will burn plenty of calories!

Anything new at the gym

Gyms are always testing out new equipment, so why don’t you try mastering one of them when the weather is messing with your exercise routine! You can even rediscover some of your old favourites or sign up for workout classes.

Indoor facilities

There are many ways to burn fat without being outside like swimming a few laps in an indoor pool or running a couple of miles on the treadmill! One of the best ways to lose weight is to pick up an indoor sport like action soccer or action netball.

Lifting weights

Heck, if you wanted to burn fat you don’t even need to step foot outside! You can always use small hand weights and resistance bands right inside your house to burn fat. Lifting weights to build muscle can be very useful in burning fat, simply because muscle helps burn fat.

Indoor exercise may not always be ideal, but does keep you active and on track to reach your weight loss goals. But once again don’t forget have at least one rest day to allow your body to recover! And if the weather turns nasty and you where due to go outside exercising, you can always swap that exercise day for a rest day!



Source by Justin Greyling

Share Button

Why Should You Install LED Boat Lights?

Share Button

Your current lighting setup works just fine right? You can see your decks well in the night, you get by just fine with that single small reading light in the cabin, and heck, you just make sure you’re extra careful when running your systems so you don’t end up draining the battery banks. So why bother going with LED lights instead of those nice cheap incandescent bulbs you’ve been using all these years?

If this is your way of thinking when it comes to the lighting onboard your boat, the chances are very good you are wasting a lot of money and dealing with a lot more hassle than you probably realize.

Most boaters are well familiar with the need to manage onboard electrical power. Since all power for electrical devices must be produced, stored and supplied independently of onshore sources, boaters must rely on generators, solar panels, wind turbines and battery banks to produce and store electrical energy. Because of this, the amount of power that can be generated and stored is severely limited and close attention must be given to maintaining adequate power levels for the operation of vital equipment as well as luxuries in order to avoid increased costs through excessive fuel consumption and potentially dangerous situations where battery reserves are depleted to the point of being unable to start engines or operate safety lighting.

Because it can become expensive to run generators frequently, and alternative power sources such as wind and solar are limited in their ability to replenish supplies, most boaters resort to rationing power use. While larger battery banks and generators can provide increased generating and storage capabilities, the cost of fuel still remains a stumbling block and only increases with such additions. Many boaters will resort to battery powered lamps, running only a couple small cabin lights sporadically in order to make it possible to at least get to the head without banging a shin, and running the most minimal anchor and mast lighting possible while still meeting compliance with regulations. While all of these things and more can indeed reduce power consumption, they take away from the overall ability to enjoy your time on the water, and this is a serious problem when we consider that for most boaters, the whole point is to enjoy the luxury and relaxation that comes with spending time onboard.

Although they are not the most power hungry devices, lights represent a major part of the electrical system and due to their critical nature, are impossible to do away with entirely. It is ironic indeed that for something which is so important to the general safety and functioning of onboard activities, they are often treated as non-essential when it comes to power management. The good news though, is that this no longer has to be the case.

The most important benefit boaters can realize from switching to LED lighting onboard their boat is greatly reduced energy consumption. Whereas a typical 25 watt halogen bulb may draw over 2 amps and produce only 425 lumens, an LED fixture producing 500 lumens can use only 10 watts and pull less than 1 amp. That is more light output using less than half as much power. This kind of efficiency is impossible with normal incandescent lamps and allows you to produce more light, using fewer fixtures. For a boater who is loathe to leave cabin lights on for any length of time, this means you can install half as many lamps and produce the same illumination, while cutting the power draw by up to three quarters. This mean no more reading by the weak yellowish light of a battery lamp, or making so with dim cabins and hard to work in galleys or cockpits.

While LEDs do cost more initially than traditional lamps, they provide other cost saving benefits besides efficiency, which further help to offset their higher price and provide net savings over the long term. Lamp life is one of these peripheral benefits, and it can be extended over ten times as long using LEDs. A typical incandescent bulb will last approximately 500 to 1500 hours, causing frequent outages and the need for equally frequent replacements. Each time you replace that lamp, you incur additional costs. An LED boat light on the other hand will last in excess of 50,000 hours on average. That means that you would have to replace an incandescent lasting an average of 1,000 hours 50 times to equal the longevity of your LED lamp. If we say your incandescent bulb costs $1.00, that’s $50.00 over the course of 50,000 hours. With LED bulbs now available for as low as $24.00 for quality units, it is easy to see a net savings in maintenance and replacement costs alone. Add in the power and fuel saved as well, and it is clear that LEDs are actually more cost effective over the long term.

Two other very notable improvements LEDs offer over incandescent lamps are cooler operation and much greater durability. Most boaters are well aware of how warm it can get below decks in the summer. Now imagine placing several small heaters in that small cabin as well. Things can get rather warm quite quickly, obviously. Well, this in effect is what you are doing when you turn on those hot running halogen or incandescent cabin lights. This in turn causes air conditioning to run harder and more often, using more fuel and draining more power. LEDs on the other hand run cool enough to touch with your bare hand, even after hours of operation, reducing the heat added to the cabin, often the AC needs to run, and improving your overall comfort.

LEDs can also survive rough handling that would destroy a normal glass incandescent bulb. LEDs have no wire filament, no glass, no gases or mercury, and can withstand jarring, vibrations, and even impacts from dropping or accidental hits without any change in performance.

Overall, the reasons for switching your boats lighting system over to LEDs are numerous. You can run more of them, and for longer periods. They need less maintenance and cost less to operate over their lifetime. And last but certainly not least, they’ll allow you to spend less time worrying about maintaining your battery reserves and more time actually enjoying your boat. And that, friends, is why you should install LED lights onboard your boat.



Source by Dexter Luck

Share Button

What is Paintless Dent Repair?

Share Button

Many times, you are simply in disbelief that your vehicle is sporting another dent or ding. It just doesn’t take much to mar the beautiful car’s surface. Anything from an errant rock to an out-of-control shopping buggy can all pose a significant hazard to your car’s exterior. One of the best ways to repair these types of dents is with Paintless Dent Repair. However, there are certain requirements for the types of damage this process will be most effective on.

What Types of Damage Can Be Fixed with PDR?

The most common types of damage that are easily repaired with PDR are those that are in a door panel or fender. The dents do not have creasing or painted removed. They also cannot entail the trim area and need to be a certain distance away from the edge of the part.

What Is the PDR Process?

This process sounds rather simple; however, it takes a great deal of training and experience to get it right. The first step in the process is to gain access to the area behind the damage. This involves removing the inside door panel or perhaps removing a tire for access to a wheel well. Then, with the use of several specialized tools, the metal is massaged from behind. Once complete, there is no sign of the repair. It’s also much less expensive than a traditional repair in a typical body shop. The entire time to do the repair only takes about one to two hours. If you’ve ever had your vehicle in a body shop, you know that it can days for your car to get fixed. This not only is inconvenient, you could not have access to your vehicle for days.

Let the Company Come to You

Almost all of the companies that offer this type of service offer mobile service as well. They will come to your location, such as your work or home and take care of the car. It’s a very convenient way to get your car looking fantastic again. This is also a great idea for a leased or rented vehicle, too.

In Closing

The key to this process is choosing someone who has the training and experience to effect the repair properly. If not, you could end up with more damage than before and it could be very expensive to fix! For the best results, only use a PDR company that is well established, insured, and bonded.



Source by Steven Magill

Share Button

How to Reuse Plastic Bags

Share Button

Using reusable bags has worked on with grocery stores across the country, but many other types of businesses are slow to catch on. At some point or another, you'll most likely be taking a plastic bag from some type of store. When you accumulate plastic bags, how can you reuse them?

Plastic bags become popular because they are a cheap, affordable way to bag groceries and goods. The bag could be thrown away after a single use. While it's convenient in theory, disposable plastic bags have grave consequences for the environment. A single plastic bag will never disappear. Unlike other materials, plastic does not biodegrade, it simply breaks apart into smaller pieces of plastic (which is actually far worse than larger pieces because they can not be collected).

Plastic bags:

  • Never biodegrade.
  • Cause animals to suffocate and die.
  • Use fossil fuels to create them, increasing our dependence on foreign oil.
  • Are an eyesore and get talk on car antennas, mufflers, and twisted into engines

Plastic grocery bags can first of all be recycled. Many grocery stores will accept plastic bags to be recycled (usually you'll find the receptacle near the entrance or near the can redemption center).

Recycling Plastic Bags vs. Reusing Plastic Bags

Recycling almost always uses more energy than reusing. By reusing, you'll be giving the product a second life. When your recycle something, you'll be using energy to turn that product into something else, which can use energy and produce emissions.

Five Reasons You Should Bring Your Own Bag

Plastic has a hugely negative effect on the environment, and also on our society. The cons far outweigh the positives of these disposable nuisances. Here are a few reasons you should consider switching to reusable bags instead of plastic:

  1. Bringing your own bag means you'll be carrying less to and fro. Most reusable bags hold far more than traditional disposable bags. Less trips back and forth from the car!
  2. Each time you use your own bag, you'll get a small credit back from grocery stores. It's usually between 5 and 10 cents, which can add up over time.
  3. Using your own bag reduces our dependence on foreign oil. Plastic uses fossil fuels, which are large found in countries that do not have the best intentions Western World. Cast your vote for locally made reusable bags instead.
  4. You will not have to worry about throwing away, recycling, or reusing your disposable bags. By reusing your own bags, you'll have less clutter and less trash.
  5. You'll be sending a green message to your children. When they see you using their own bags, they'll take notice and want to do the same in their lives.
  6. If you'd like to reuse your plastic bags , they have hundreds of uses.
    Ways to Reuse Your Plastic Bags

    • One of the most popular ways to reuse plastic bags is to use them as a trash bag.
    • Place them in small trash barrels in the bathroom, bedrooms, cellar, and near the cat's litter box.
    • Another popular use for them is to use them as doggy poop bags. If you're going out for a walk, bring along a couple of these bags.

  7. You can also reuse plastic bags as packaging. If you're shipping out an item on eBay or shipping something to a friend, the bags can act as a cushion, much like packing peanuts, if you use enough of them.
  8. Keep a plastic bag in your car to contain all of the trash that accumulates in your car. Then, simply tie off, throw away, and use another bag.
  9. Donate your plastic bags to a local thrift store or charity. These results them from having to buy brand new bags.
  10. Post an ad on Craigslist for your bags. A local business may want to use them (you can not beat free!).
  11. Use your bag to contain messy foods and leftovers that might otherwise leave spills. This is especially useful with soups and liquids.
  12. Think of things that you traditionally would use plastic for and replace them with your grocery bags. If you usually put your lawn leaves in trash bags, save up your larger shopping bags and put the leaves in there instead.
  13. Wrap a bag around bags of flour, sugar, and other messy baking ingredients. This can help contain the mess and make for an easier clean up.



Source by Danielle Nihill

Share Button

Bench Press 101 – A Step by Step Guide on How to Increase Your Bench Press

Share Button

This article is intended for beginner/novice lifters, but many intermediate and advanced lifters can also benefit from it. I will take you, step by step, from setup to lockout and everything in between. On the surface, the bench press looks like a simple exercise but, in reality, at the competitive level, there are a ton of different little techniques that can maximize your press. Always remember, you are not a bodybuilder trying to isolate your chest muscles. This is a total body movement, and almost every muscle in your body is used to perform a power lifter-style bench press.

The Setup

When you get ready to bench, you will want to position your body in the best way to maximize strength and minimize the chance of injury. You will have to focus on several things during your setup:

1. You want to pull your shoulder blades down and back as hard as you can. Think of trying to touch your shoulder blades together.

2. Your chest should be as high as possible. You will want to arch your upper and lower back while making sure your butt stays in contact with the bench. There should be space between your lower back and the bench – at least enough for someone to slide their hand under you.

3. Foot Position. There are two (2) basic styles of foot position: feet in front and feet tucked back. Each style has advantages and disadvantages. I have seen great benchers use both foot positions. You have to try out both styles and see which one works best for your body style and bench press technique.

FEET IN FRONT: This is the most common foot placement. This foot placement has two advantages. First, it puts you in position to generate the maximum amount of leg drive. The second advantage is your wide base will help with staying balanced throughout the entire lift. Your knees will be bent so that your upper and lower leg will be pretty close to an 80-110 degree angle. You will be driving your foot forward so your toes want to go through the front of your shoe without your foot moving on the ground. Try to picture yourself using the same force to perform a leg extension with the only difference being that your leg will remain stationary. The force you generate from leg drive is going to enable you to maintain the upper and lower back arch and help transfer your total body strength into the lift.

FEET TUCKED BACK: This is a less commonly used foot placement technique. If you are not flexible, it will be hard to get into this foot position. This foot placement doesn’t allow you to generate as much leg drive force. It is also tougher to maintain your balance through the entire lift. It does, however, have one major advantage over the feet in front position. The feet tucked back position will enable you to have a more aggressive arch. By having a bigger arch, you will shorten your range of motion.

When you get into position for your feet tucked back, you will most likely be on the balls of your feet. I have seen a couple lifters able to have their legs back with their feet flat on the floor, but that is very rare. Your upper and lower legs will form around a 60-40 degree angle. You will want to drive your heels down while doing the same leg extension pressure.

4. Finding your best hand position on the bar. Every lifter has their own preference grip width. Most lifters prefer to have their pinkies, ring, or middle finger on the smooth ring on the bar. A closer grip gives you better strength out the bottom, but it increases the range of motion. A wider grip is tougher off your chest, but it shortens your range of motion. Experiment with different hand positions to find out which one works best with your style of benching. Now that you’re set, grab the bar with your thumb wrapped around the bar. Squeeze it as hard as possible. This will activate your muscles and let your body know you’re about to lift. Once you grab the bar, if you feel like your coil loosened up or your shoulder blades aren’t as tight as possible, you should try to reset and get tighter while you maintain your grip on the bar.

5. It’s time for your hand off. A good liftoff man is worth his weight in gold. You want him to lift and bring the bar out to you until you’re in an optimum start position. I prefer for my start position to be lined up with the bottom of my chest. Make sure your liftoff man doesn’t lift the bar too high – that will open up your shoulder blades and take you out of the proper position.

6. Now that you have the bar in your hands, you are ready for the descent/negative. The speed of the descent is different with every lifter. Whatever speed you feel strongest with will be your best speed. A bodybuilder might have a 90-degree angle between his upper arms and body. You should try to have a maximum of a 70-degree angle, closer to a 60-40 once you get used to it. Always make sure your elbow and wrist are aligned. If you try to touch the bottom of your chest and your elbows aren’t tucked enough, then your wrists will be ahead of your elbows; that is a dangerous position to be in. Slowly try to touch lower and lower until you find your strongest spot. It should be around the bottom of your chest, or a little bit lower than that if you’re tucked enough and have a decent arch.

If you are benching right, you will feel it in your back and lats. Try to bend the bar as it goes down. You will be bending from your pinkies rotating your hand so your right hand is rotating clockwise, and your left hand is rotating counter-clockwise. As the bar descends, you want to activate your lats and try to think of it as though the bar lowering your body is a rubber band. You are building up kinetic energy and, when it hits your chest, you explode with all that built-up energy. If you are benching right, you will feel it in your back and lats.

7. As you press the bar, it is natural for most people’s elbows to flare out. Try to keep your elbows tucked until at least halfway through the press. You will experiment and discover what works best for you; whatever way enables you to bench the most will be your best option. Every work set rep should be pressed with maximum effort. You should always explode out the bottom, and use that momentum to your advantage. Speed and momentum are your friends; using speed and max force off your chest will become second nature. When it is time for max effort lifts, you will instinctively press right through any natural sticking points.

8. Now, enough reading. Get under the bar and smash a PR.



Source by Eric Spoto

Share Button

Voice Over Microphones – How to Choose the Best One For You and Your Budget

Share Button

The biggest mistake voice over artists make – and that includes some professionals – is using the wrong microphone. It can wreck your work. If you market yourself on Voice123.com or Voices.com, the wrong microphone will insure you do not get hired, or if you do, that you will not get hired by that same person again.

Here we'll look at the three types of microphones most often used, their strengths and weaknesses, cost, and how to determine which one (s) to go for.

We'll talk about the types, then look at specific brands, models, and prices.

Before we start, the most important thing I can say to you is that your microphone is the most important part of your entire audio chain, no exceptions. You can have the most fabulous gear in the world downstream from the mic, but if the mic does not cut it, it does not really matter about the rest of that gear. On the other hand, a terrific microphone followed by average-priced gear will give you a superior audio product.

What are you looking to do? Are you looking for a mic that's smooth and sweet, or hard-edged and in-your-face? Are you male or female? If you want to do movie trailers and screaming car dealer ads, you need a different mic than if you're doing "guy or girl next door" – realistic – voice work, or standard announce voice work. Here are the types of mics to consider:

Dynamic

Dynamic microphones are what you see in radio stations and are what live vocalists (singers) most often use. They're rugged, reasonably good-sounding, and okay for most voices, meaning one might not sound absolutely fabulous on your particular voice, but it will not sound awful, which is not true of other types, including some very expensive microphones. A dynamic also is not nuanced. The part that pics up your voice, the diaphragm, is connected to a coil of wire; Air movement from sound makes the coil move between the poles of a magnet. The sound has to overcome the mass of the coil, and very small sounds do not get through.

This does not make them bad. Rush Limbaugh's Golden EIB microphone is a dynamic, and, again, most radio stations use them. They are good general-purpose mics, and many voice over pros use them. They are equally good for male and female voices, and you can do most any type of style with them.

If you're on a budget, a dynamic is the only choice, because the other two cost a lot more for ones that are worth it. There are cheap versions of the other two, and you do not want one!

So if dynamics are so useful, why spend more for a condenser or ribbon?

Condenser

A condenser microphone, of which there are two types, transistor and tube ("valve" in Europe), does not have the moving coil of wire attached to its diaphragm. It modifies an electrical current generated by an external power supply (found in most computer interfaces or with an external power supply, see your dealer for info, or internal batteries). Without the mechanical resistance of a dynamic mic's coil to overcome, a condenser is far more sensitive to nuance, and therefore sounds much more intimate.

Condensers come in two flavors: transistor and tube. A tube condenser, which is an expensive instrument (there are cheap ones and they make good paperweights but not microphones), is almost always the very best way to go. They sound very intimate and full, and have a great up-front sound without being aggressive. They are quite subject to problems from non-vocal speech components – 'f', 's', 'p' – and require a pop screen (see your dealer). Tube mics also produce what's called harmonic distortion, which we do not consciously hear but is responsible for what's called "tube warmth" (nothing to do with temperature!) And sounds quite intimate.

Condensers come in two other flavors: large diaphragm and small diaphragm. Large diaphragms are for when you want a big, intimate sound. Small diaphragms are said to be more accurate. However, the right one for you is the one that sounds best after making several-minute recordings with each and seeing if one is more fatiguing or if one just plain sounds better to you than the other. There are no rules. Both kinds are used for voiceover.

Many voice over artists prefert tube condensers over transistorized ones, but in all cases, what sounds best on your particular voice is what you should get. How to choose a mic? We'll get to that in a minute.

Ribbon

Here's the third type, in a class by itself: the ribbon microphone. While dynamics and condensers 'hear' with diaphragms, a ribbon microphone "hears" with a short, narrow, and very thin piece of corrugated aluminum suspended between two poles of a strong magnet.

You've seen the big, pickle-shaped microphones on Letterman's and Larry King's desks. They are RCA Model 77 ribbon microphones (used as props in this case), invented, I believe, in the 1930's. They were found everywhere for half a century. RCA quit making ribbons in the 1970's, and an enterprising genius named Wes Dooley bought all of RCA's stock ribbons (the ribbons themselves) and probably single-handedly re-introduced the ribbon microphone to the US market. His company is called AEA, and even the AEA logo is so designed as to closely resembled RCA's logo.

Ribbon mics are warm and smooth, jazz guys like to record with them, they're very nice for ladies' voices, and for certain male voices they add a nice satisfing depth. They also have a low output, which means that you have to crank up the input on your system to get a decent level from them. But raising the input results what's called the noise floor, and you can end up with a recording where you can hear hiss in the background. Wes and other ribbon mic manufacturers deal with this problem well, however, and some companies are making preamplifiers (talk with your dealer about this) specifically designed for ribbon mics.

Whether a ribbon – or any mic, for that matter – will sound good on your voice can not be known without actually trying one out. Ribbons are quite sensitive to moving air; If you blow into one to test to see if it's on, there's an excellent chance you'll destroy the ribbon. When ribbons were in common studio use, they were 'bagged' – a fitted bag was put over them – just to move them from place to place in the studio, to avoid ribbon damage from the air passing across them as they were moved .

Brands

Dynamics

There are a million brands, which of course goes for condensers, but not that many ribbon brands.

Not to worry, because there are several industry standards with which it's hard to go wrong. Here are the three most popular dynamics, and they probably outsell all the rest put together:

Electro-Voice RE20
Sennheiser 421U (see dealer about the specific one for your purpose)
Shure SM7
———
Shure SM57 / SM58 – less expensive and can be used if you do not have the money for the others

These mics, except for the last two, are in the $ 350- $ 700 range. Although each has a characteristic 'sound,' they are pretty close together in that respect. Each is well-made and dependable over the long haul, as in decades.

The Sennheiser, and, I believe, the SM7, have what are called proximate effects: if you get right on top of them they accentuate the lows. Many announcers in radio stations like to eat them; They want that deep "Voice of God" sound. They're better used at a distance of 6-10. "The RE20 is known for its lack of the procurement effect. Etc. The RE20 was also made under a different model name, PL20. Instruments and is no longer in production. I found a PL20 for $ 150 and am still jumping up and down, for the average used price of a PL20 or RE20 is double that.

For price-to-quality, none of these mics can be beat.

Condensers

Two flavors, here: transistorized and tube. As mentioned above, a tube condenser, like any well-designed tube device, generates overtones, which our ears perceive as "warmth." I say well-designed, because ever since tubes were "rediscovered" about 25 years ago, a lot of low-priced gear with a tube or two in them has hit the market, but they are not necessarily designed by people who understand exactly what They do nor how to design a tube circuit for best effect. This section deals with condensers in general.

Probably the most-recognized condenser mic name in the world is Neumann (pronounced NOI-man), and its most popular model is called a U-87. They sell new for around $ 3500, around $ 2000 or less used. A Neumann either sounds incredible on your voice or it sounds honky. It is the microphone National Public Radio uses exclusively.

It is found in just about every recording studio of any size. It will love your voice or hate it.

There are more expensive Neumanns, and a series of low-priced models prefixed with the letters TLM. A good number of voiceover artists use TLMs (<$ 1000); In my opinion they are not nearly as natural-sounding as the U-87 or a good dynamic. I had one but sold it after a few months. It could sound really good to your particular ear, however. I make this point because tastes different, and it is surely true that one voice can sound bad on a certain mic and superb on the next voice. So how does one choose? We'll get to that in a sec.

First, you must use a pop screen on a condenser. This device stops those blasts of air from non-vocal speech components, most notably "P" sounds, to which condensers are especially sensitive. Put your hand in front of your mouth and say "P." Feel the air? If that blast hits a condenser, let's just say you do not want to be wearing headphones at the time. Now, it's a good idea to talk across (at 45 degrees) not straight into, any microphone, because all of them will react badly to P pops; It is just that condensers REALLY react to them. Many RE20 users put pop screens in front of their mics even though most people do not use pop screens with dynamics.

Cheap condensers: a big no-no.

Cheap condensers are all over the market. You can buy a microphone with a nice spider shock mount and in a beautiful aluminum flight case all for $ 75. Um, I do not thin 'so, Looooxy. They are unnaturally bright at the top end and boomy at the bottom.

The really nefarious part of this is that, if you're just starting out, your ear is easily fooled into thinking that this sounds good. It does sound sort of exciting, but it is extremely fatiguing to listen to a recording made on one. As Phil Spector famously put it, "It's all in the middle." Americans like to crank up the treble and bass. If you have a mic delivering lots of highs and lows, and someone boosts the highs and lows on their music system, your work will sound worse than awful. Expensive microphones have rolled-off low ends and smooth high ends. Upon first using one you may even think, "Wow, what's the big deal about this thing? It's boring." No, it's natural. Unboosted highs and lows. In other words, it sounds like you, not you-through-a-microphone. That's as it should be.

Remember, you are competing with people who own high-end condensers, and that's how they sound. I'll take a $ 400 dynamic over a $ 400 condenser just about every time.

Ribbon microphones

I have experience with exactly one ribbon: an AEA R84. It sounds really good. It's an updated version of an industry-standard RCA ribbon, the Model 44, invented long ago and used forever, like the 77. It's tres cool-looking, and comes with a snarky-looking padded, fitted maroon bag for transport and protection. It's about $ 990.

There are other ribbons that have excellent reputations, more hitting the market all the time, see your dealer. I'm not aware of ribbons being used that much for voiceover, but I think it's because a great number of people do not know about them. I think it's also due as much to inertia as anything – everyone learns what everyone else is using and continues suit. Also, ribbons do not have the in-your-face sound that dynamics and especially condensers have.

How to choose the right mic for you

The really best way is to call a professional recording studio and book an hour or so of their time, and have them set up an array of mics around you and test read you, each mic going to a different track of a recording. It's infinitely better to match the mic to your particular (and unique) voice than to get just anything and try to make it fit using equalization (Google "equalization for voiceover" and read it!). I recommend you test no fewer than five mics, making sure to include all the ones listed above except the Shure SM57 / 58. When you listen to yourself recorded on each one, the best one will usually make itself plain, and it's a good idea To ask the recording engineer's opinion, for s / he knows what to listen for. My method is to listen to the records of the first two, choose a winner, compare it to the third one, choose a winner, compare it to the fourth, and so on. Then do it again, only have the engineer mix up the playback order.

Do not try this test in an amateur home studio. They almost certainly will not have the mics you need to make the test meaningful, and the person recording you will almost certainly not be competent to evaluate which mic to use for voiceover; Most home studios exist for the purpose of recording music and sung vocal, not voice acting and voiceover.

What if you do not have a studio within 50 or 100 miles, or their rates are too high (although I think paying $ 100 to test several thousand dollars' worth of microphones will save you unbelievable heads, sending mics back, etc.)?

Here's what to do: if your budget allows, buy either a Neumann U-87 or a Lawson L-47 MPII. The Lawson is around $ 2000, or $ 1500 bucks less than the Neumann. The Lawson is the mic I have used for nearly 10 years. It sounds like Disney, but even more importantly, I have yet to record a voice on it that has not sounded really good.

It is sold factory-direct through a fella named Gene Lawson in Nashville, at Lawsonmicrophones.com. If you call them, you can talk right to Gene. He's a great guy.

Absent that kind of budget, get an Electro-Voice RE20, Shure SM7, or Sennheiser 421U (they come with a couple of variations so tell your dealer that you're using it for VO.

If you're not sure whether you really want to be a VO artist but would like to give it a trial shot, get a Shure SM57 or 58. They are $ 100 dynamics. As I said before, they are okay, and never sound bad on anyone's voice.

Where to get it?

If you're going to get an RE20 or Sennheiser or Shure, get it from your local music store (the best choice because service is right there, no mailorder hassles). If you do not have one, go online to one of the big catalog outlets such as Sweetwater, Full Compass, Zzounds, or Guitar Center. They have fairly liberal return policies and are easy to work with. They sell a lot of stuff and have competitive reputations to maintain. Plus, their prices are usually identical from piece to piece so they have to make up for it with really good service, all to our advantage.

If you've got the bucks for a $ 1500 – $ 2000 + condenser, go online to SoundPure.com. (Lawson are sold factory-direct only at Lawsonmicrophones.com) Sound Pure has professional sound recordists to talk to, and at those prices you need to talk to pros. Not that the catalog stores do not have pros, but their level of expertise varies. I've talked to guys who knew nothing about what I wanted and guys who knew a lot; At Sound Pure they're all pros and they are really interested in getting you what you need and not a penny more.

Tell them everything you want to do, what other gear you have, what to buy if you do not have any gear yet. They really give a great big rip about their customers and about the pro audio business in general. I can not say enough good about them. In case you're wondering about all this nice stuff I'm saying about Lawson and Sound Pure: not only am I not getting paid by them, they do not know I'm writing this article!

To sum up: If there's a pro studio near you, book an hour and test their dynamics and condensers using the method above.

When you're ready to buy, if you want to spend $ 200- $ 700, get a dynamic: Electro-Voice RE20, Shure SM7, or Sennheiser 421U. Check your local music store first – everything's so much easier that way. From $ 1500 and above (which your local store probably will not have) get a tube condenser: Lawson L-47 MPII from Lawsonmicrophones.com, or for others, go to SoundPure.com and call them. Re the RE20, EV also makes an RE27. Some people really like them, some people really do not. I'd go with the RE20.

I've worked for years to get a good sound and am writing this to try to save you some time in finding your great sound.



Source by Michael K. Holmes

Share Button

Everything You Wanted to Know About Fixed-Based Operator Services

Share Button

If you are an investor or equity sponsor in the field of aviation, you may have many questions regarding on-airport services. In North America and parts of Europe, the roles of different operators and service providers at an airport are well defined, while in other countries local ground handlers are associated with many of those same operations. In this post, we will take an overview of different services at a public airport, along with the things you can expect, especially if you need direct assistance in finding the best service provider to meet your needs.

Overview of Fixed-Based Operator (FBO) services

Fixed-Based Operator (FBO) services basically operate key airport infrastructure and facilities in aviation, usually under a long-term lease directly from the airport. The services can vary depending on the nature and size of the airport, but the core profile often remains the same. FBOs are responsible for a number of different roles. They provide critical line service functions such as the handling, fueling and hanging of private aircraft, manage the passenger terminal, crew lounges, and other facilities, and may also offer certain maintenance and repair services. The size and location of FBOs determine their services to a large extent. Full-service FBOs are extremely popular in North America and Europe, while in other areas such as Australia and parts of Asia the demand for these services is increasing.

Overview of ground handlers

Ground handlers, on the other hand, are usually licensed by the airport as a concessionaire. They may provide the general services that are required in the sector, mainly at airports which do not possess the requisite infrastructure for full FBO services. These companies mostly deal with below-wing services, although in some cases they do deal with above-wing services. In this context, it’s important to understand the distinction between above-wing and below-wing services.

1. Above Wing services – These include a wide range of services, including some of the services that are offered by FBOs, such as ensuring catering onboard, cleaning flights at technical stops, following and managing passenger and crew, and anything that’s directly related to the flight’s management. These services also include managing the ground accommodation of crew and passengers, besides concierge services.

2. Below Wing services – These services include aircraft handling, fueling, management of ground support equipment, movement of baggage, and any required hangar services. All ground handlers who do below-wing services must have specific operating rights from the airport, own the necessary equipment and be specifically trained for various functions such as towing, marshaling, fueling, etc. They must also have proper insurance in place at a minimum amount specified by the airport. In some parts of the world, ground handlers may need additional certification.

Other areas

When it comes to aviation infrastructure management, FBOs specialize in different areas, although they are all expected to perform certain core line functions. Fixed Base Operators understand the needs of private aviation, whether corporate or recreational, and can offer direct assistance to the flying public. Some companies may have additional experience in facility management as well. If you have aviation assets and are seeking professional management, you should closely review a prospective service provider’s experience and breadth and depth of service offering. If you are seeking help for international assets, then the service provider should have a proven track record in global operations.



Source by Steve Ward

Share Button

Golf Putting Tips: 3 Keys to Improvement

Share Button

As golfers we all want to lower our scores – it seems we are never quite satisfied. At the end of the round we see where those extra strokes came from and it's usually from the short putts we missed.

It's a fact in 18 holes of golf 40% or more of our score is from putting. It only stands to reason that the easiest and the quickest way to lower our scores is to improve our putting by eliminating the three putt greens. This can be done simply by adjusting your set up position.

1. The Grip: To become a good putter you have to start with a good grip. Do not grip your putter the same as you would your other clubs. We're taught to grip these clubs more with our fingers and this grip does not work too well with the putter. The correct way to grip a putter is in the palms of your hands right along your life lines with your fingers wrapped around the putter handle. This will cause your arms from the elbow to be directly in line with the putter shaft. Light grip pressure is also real important. On a scale from 1 to 10 it should be around a 5. I found that oversized putter grips work very well in developing the correct grip and pressure.

2. The Eyes: In the set up position your eyes have to be lined up inside your target line. If you get your eyes too far over the golf ball, this will cause you to make a bad stroke, you may pull the putt or push it but the ball will not go where you intend it to end up.

To check this, take a golf ball, position it under your right eye (if your right handed) drop the ball, the ball should land somewhere behind the hossel of the putter. If it does, this is where you should be every time you put the ball.

3. Putter Shaft Position: The shaft of your putter should lean forward just left of your belly button (if you're right handed). This will cause the ball to roll with over spin, this in turn will enable you to control the distance of your putts with more consistency. When you lean the putter shaft back in your putting stroke this adds loft to your putter, which creates back spin on the ball and it makes it hard to control the distance.

You are now ready to make smooth and accurate putt. Hold the putter in the palms of your hands, make sure your eyes are in position then lean the shaft forward a little and make the putt.

Practice these simple set up tips and you will become a much better putter in no time at all.



Source by Ken Bolin

Share Button

How To Prepare Your Pet Dog For The Arrival Of A Baby

Share Button

A whole lot of change and plenty of adjustments have to be made around the house if you and your partner are expecting a child. A room has to be turned into a nursery, the entire house should be baby-proofed and some areas have to be rearranged to welcome the baby. While this change can be both exciting and overwhelming for parents-to-be, keep in mind that your pet dog is going through it, too. He, too, must be prepared for the arrival of the baby.

Such a huge change can be confusing to a pet – here’s how you can help them transition easier:

Plan ahead

Will the dog be allowed in the nursery? Can he go near and kiss the baby? Although it may seem trivial, these are questions that need to be addressed beforehand. Getting your dog ready for the arrival of your baby may also require a refresher on basic training such as SIT and STAY. It helps to list down what needs to be worked on, when to start training and who will train the dog.

Work on manners

Aside from refreshing basic commands, it is also important to fix some behavior issues that your pet may have before the baby arrives. This could be consistent barking, jumping up on people or simply not being obedient. Behavior like this re not ideal for new parents taking care of a newborn. Work on these issues as early as possible so that they are improved by the time the baby comes.

Familiarize them with new smells

Familiarize your furry friend with things that he can associate with the baby like baby powder, cologne and wash. Once he gets used to these new scents, it will be easier for him to recognize and welcome the newborn. You can also let him sniff some of the baby’s toys and teach him that they aren’t for him to play, chew on or take.

Practice with your dog

A few weeks before your baby arrives, show your dog what is to come. It is ideal to practice using a doll – change its diapers, rock it to sleep or feed it to help your dog get used to these kinds of scenarios. If your dog starts barking or getting uneasy, it is ideal to correct these behaviours so that he’s better prepared when the real thing comes.

Doing these simple things will help your pet dog prepare for the arrival of your newborn baby!



Source by Mary L. James

Share Button

Outdoor Sports Lighting Options – Several Considerations to Assist With Your Purchasing Decisions

Share Button

This category of products has developed rapidly over the past 10 years. With so many new, exciting and flexible options, it can be very overwhelming to not only a first-time buyer but an experienced outdoors person as well looking to expand their existing inventory.

Historically conventional battery, gas, candle or liquid fuel were the standard. While all of these options are still widely used, much safer, portability, significant durability, sizing options, flexibility and environmental options have evolved to enhance your selection and overall experience. The intent of this article is to touch on some of those options available to buyers today.

Category Options:

With the invention of the rechargeable batteries, solar, hand-generated power and other flexible applications have added greatly to the popularity of rechargeable battery powered lighting. These options have been particularly popular for hikers and off-road bikers, who are always short on room and looking for lighter overall weight and durability options in their backpacks. Whether you are Camping, Hunting, Fishing, Off-Road biking or Bird Watching there is always a time and place for hands off lighting applications. Options available can be for helmet, caps, headband style, mounted on handlebars of bikes, or even remote controlled directional on boats.

The flexibility now in lanterns spotlights, floodlights, flashlights, and torches are numerous as well. They can be hung from a tent, tree, collapsible, expandable, and handheld!

Lumen’s Performance

The invention of LED bulbs has had a dramatic had an impact on both outdoor and indoor lighting applications. LED bulbs to provide not only great lumen performance but life, duration, and durability over the typical filament bulb. A typical LED bulb has the life expectancy 40 times that of a traditional bulb. That coupled with the hardness contributes to their advantage over a filament product. A LED bulb has a greater upfront cost but your return on your investment far outweighs the durability and reliability of the typical filament bulb.

Lighting Power Options

The ongoing upgrades for a buyer’s rechargeable battery options continue to evolve greatly as well. There are a number of rechargeable lighting options that depend on a charging unit that can be connected to recharge a user’s power. A buyer using this type of lighting option in the outdoors as your main source of lighting may be suitable depending on the life of the battery and whether ready access to the main power source is readily available to use in conjunction with their recharging unit.



Source by Jim Staples

Share Button

The Ban on Greyhound Racing in the ACT

Share Button

This is a big issue in the Australian Capital Territory as the Greyhound Industry gears up for a legal challenge to the governments disbandment of it. The question is whether it constitutes a sport or a business that exploits innocent animals and causes them pain and suffering. The other agenda at work here is the clamp down on gambling in the territory. One can’t be seen to support a racing industry while denying other forms of it.

The feeling in the political arena is that people are spending wildly on things like poker machines and other forms of gambling. Many addicted to it have become homeless or dependent on charities and the like as a result. There is also the question of cruelty in the greyhound business when secret cameras filmed live bating in training sessions.

The animals in these images were rabbits, kittens, and possums, who were ultimately ripped to pieces. That was after being tied to a machine and driven at speed around the track with a pack of dogs in hot pursuit.

As a pet owner and one who respects all life this type of thing has disgusted me. Even more so as years ago when I gave some kittens away and a man told me he only wanted one to train his dogs. He never got it from me and my words to him were not so kind.

What is in the human psyche that supports this type of animal cruelty? That is what the Minister who issued the ban has also asked. Surely it is up to society to stand behind his judgement and let the matter proceed to court where hopefully the judge will favour the victims over the ones who make money from them.



Source by Norma Holt

Share Button

Cable TV – Do You Experience These Cable TV Problems Like My Friend Ted?

Share Button

Cable TV

My friend Ted is very fond of talking. To be honest, so am I!

Whenever I meet Ted, we discuss any and everything under the sun. It generally includes many things with which we are not really concerned and which many people like us would never bother to even think about. But once we start our discussions, unknowingly, we become so very passionate about the whole thing that anyone who happens to overhear us would feel inclined to believe that our very existence depends on that particular thing or event.

I had got my cable TV connection disconnected quite some time back and switched over to a different network. In fact, I had even told Ted just a few days thereafter as to how happy I was with the new connection. I had recommended to him that he too should discontinue his cable TV right away and switch over to the new system or even internet TV, if he so desired. But he did not feel too inclined to give up his cable TV connection.

When I met Ted last Saturday, he seemed all worked up and pretty disgusted. Soon after replacing pleasantries, he started narrating the tale of his shepherd disgust with his cable TV company. I gave him a patient hearing and have often thought about his complaints during the last 4 to 5 days. I agree with him on some of the points and say that cable TV companies do rip off their customers on these fronts.

1. Overbilling – Ted was being overcharged for programming, equipment and asserted fees, the charges for which had been reduced for new customers. These should have been automatically reduced for Ted too. But he had not taken up the matter with the cable company, he would have paid the higher amounts all his life.

2. Poor Customer Service – The 'professionally qualified' employees of the cable TV company responded to Ted in the most unfriendly manner. They kept on pretending that either Ted did not know a thing or was not able to tell his problem properly.

3. Failure to inform what the best deal was – Length lengthy discussions, the cable TV company did not straight away tell Ted as to what the best deal for him was. He was quite candid about his requirements but it seemed that they simply did not want to help.

Customers deserve better than the high costs, poor services, faulty billing and the unfair practices of the cable TV companies!



Source by Marc-Eddy Drouinaud Jr

Share Button

Getting The Most From Your Fishing Charter Experience

Share Button

Fishing is indeed a fun activity to engage in regardless of the kind of angler you are or the kind of fishing experience you love. When you go out fishing, you can decide to bring home your catch for an enjoyable meal or you can choose to just enjoy a catch and release fishing experience maybe to just test out your skills and improve on them. Anglers do not need to own boats to enjoy a great fishing experience; fishing charters offer everything any angler could ask for. But to get the most from your fishing experience you must ensure that you select the best fishing charter possible by taking a few things into consideration.

The fishing location – It will determine how many fish species you could possibly catch as well as other sea animals you could enjoy like turtles and others. The more the fishing location has to offer, the more you are bound to enjoy so always go for a location offering you a wide variety of fish species and other interesting sea life.

The fishing vessel – The fishing boat that you get should not only be sturdy enough to withstand the tides, but should also be sizeable enough to easily access mangroves, mud flats, wrecks and even reefs. You should not be forced to reschedule or cut short your fishing expedition simply because the vessel is not good enough for the current conditions. Also important to check on your fishing boat are safety well-maintained safety equipment for when a situation arises. If you are taking children with you, ensure that they are also well catered for as far as safety on board goes.

Fishing package – Fishing charters are packaged to accommodate different numbers of people and to last for different lengths of time. A package can have as many as eight passengers whereas another can have as few as four people. One package may last for four hours, whereas another could end up lasting as many as eight hours. Consider the package options available from your provider and then select according to the kind of fishing experience you want to enjoy. If you wish to enjoy some family fun, then you can choose a charter that is designed to offer families that intimate experience.

Assistance – Having a guide can prove beneficial in the end, especially if you are very new to fishing. Apart from guiding you through the waterways and to areas where there is plenty of fish, a guide can also help you learn a few things about proper fishing and even help prepare and fillet your fish if you wish to carry it home for a delicious meal.

Charter charges – Adults are charged differently from children when it comes to fishing charters. The length of the fishing expedition and type of package you settle for will also determine how much you pay in the end. Choose what you can comfortably afford, but enjoy to the maximum at the same time.



Source by Shalini Madhav

Share Button

How to Treat Bed Bug Bites

Share Button

Scientists have revealed the preliminary description of the bed bug’s sialome – proteins in the saliva that allows the bed bug to feed on humans without fatal retaliation.

Bed bugs belong to a group of parasitic insects that feed on blood. Their success in feeding undisturbed depends in part on the proteins in their saliva. These substances cause the host’s blood vessels to dilate to ease the flow of blood into its body, inhibit clotting and to prevent immediate pain and itching.

The immune system determines the host’s response to the proteins. Bed bugs can cause a number of health effects including psychological effects, allergic reactions and physical effects such as prominent blisters on the skin.

Common allergic reactions include the development of large wheal accompanied by itching and inflammation that can last for several days. Multiple bites may trigger blister-like eruptions. People with severe allergies may develop anaphylaxis. The allergens from bed bug bites are associated with asthmatic reactions.

Bite marks grouped in a linear pattern are suspected to be bed bug bites. Post-bite effect happens in 3 stages which include no reaction (development of few or no antibodies), delayed reaction; immediate and delayed reaction, immediate reaction only and no visible reaction.

Symptoms include raised and inflamed wheal at each bite site with intermittent itching for several days. Immediate reaction can happen within 24 hours of the bite and lasts for 1 – 2 days.

Delayed reaction to bed bug bites appear in 1 to 3 days followed by redness and periodic intense itching that may last up to 5 days. Delayed reactions may take up to 9 days before lesions appear.

Medical experts say people who receive frequent bites develop the sensitivity syndrome that includes nervousness, constant agitation and insomnia. Medical literature suggests a person may develop secondary infections from scratching the wheal and the bites can cause blister-like eruptions on the skin, anaemia and anaphylactic reactions and trigger or worsen asthma.

Sometimes bed bug bites develop into a hard whitish swelling that leaves a dark red spot surrounded by a reddened area. Bed bug bites usually fade after a while, but sometimes old bites flare up if the wound was not healed properly and the person keeps on scratching the wheal.

If you were bitten by bed bugs and you react adversely to the bite, you must take some steps to treat the wheal so they can heal. You should consult your physician immediately after you become aware of the bites, especially if you develop severe allergic reactions.

Home remedies and over-the-counter medications are available to treat the bites. People’s skin respond differently to treatments so please consult your doctor before using any home remedy.

Home remedies

(a) Treat the affected area with ice to soothe the wound

(b) Clean the affected area with an antiseptic soap (e.g. Dettol) before treating the wound. This prevents microbes from entering the wound. Rinse with cold water and apply a paste of coconut oil (1 tablespoon) and roasted turmeric powder (1 tablespoon). Leave the treatment on for 8 hours.

(c) Spray lavender oil on the wound for instant relief from itching. If you have an allergic reaction to the bites you can take corticosteroids. Please consult your doctor before doing so.

(d) Apply mint, garlic or cayenne pepper to the affected area after treating the wound.

(e) Black pepper, walnut and red pepper are useful herbs to treat the bites.

(f) Mix a tablespoon of salt and a tablespoon of baking powder and add water to make a paste and apply it to the wound.

(g) Apply a thick paste of cornstarch and water to the wound. Corn starch removes toxins in the affected area.

(h) Apply an astringent such as witch hazel, St John’s Wort or lemon juice to a cotton wool and dab at the wound to reduce itching.

(i) Apply rubbing alcohol to the affected area to relieve itching. Avoid scratching the wounds to prevent infections.

(j) Use a few drops of cedar wood oil with other medications (e.g. oral or topical corticosteroids and antihistamines) to treat the inflammation.

(k) Add concentrated peppermint oil, baking soda, oatmeal or Alka-Seltzer (only if you are not allergic to aspirin) to a warm bath and soak in it to reduce the itching.

(l) Honey and aloe vera can also treat the wound. The gel from the aloe vera plant has antifungal and antibiotic properties to treat the wounds.

(m) If you are not allergic to aspirin you can dip a cotton ball into Alka-Seltzer solution and apply it to the wound.

(n) Apply a light paste of aspirin mixed with water to the wound (if you are not allergic to aspirin).

(o) A hot wash cloth on the affected area can also relieve the itching.

Over the counter remedies

(a) Creams like cortisone ointment and calamine lotion reduce inflammation, itching and speed healing.

(b) Topical anaesthetics containing pramoxine relieves pain. Diphenhydramine soothes itching.

(c) Antihistamine such as Benadryl controls swelling.

(d) Hydrocortisone cream eliminates itching.

(e) Prednisone, an oral steroid, can treat itching. This medication needs a doctor’s prescription.

(f) Naproxen or Ibuprofen reduces swelling.

(g) Zyrtec and Claritin (oral antihistamines) are available over the counter to reduce allergic reactions.

(h) For systemic allergic reactions a doctor sometimes administers injections of antihistamines, corticosteroids or epinephrine.

(i) Your doctor may prescribe antibiotic ointments or oral antibiotics if secondary bacterial skin infection develops.

Bed bugs are not known to carry diseases, but they have significant public health importance. They carry at least 40 human pathogens including viruses, bacteria, protozoa and parasitic worms. Researchers have confirmed that these pathogens are not transmitted to humans through the bite.



Source by Prudence Williams

Share Button

7 For 17: Trends to Look Out for and Adapt in Your 2017 Marketing Strategies

Share Button

1. Interactive & Multimedia Content
Because 2017 will not be all about the impact of words; It will be about the experiences created for the consumer, and sometimes words are simply just not enough to educate, entertain and engage. We have all found ourselves skimming through text only to move to something new because we lose interest. For this reason alone, all brands must try to engage their ears through images, quizzes, clips, GIFs, videos, infographics – anything that will make your brand's value jump off of the screen, because words alone are like empty promises nowdays. Start experimenting and explore the endless possibilities on offer!

2. Live Streaming & Video Content
Ditch the script, improve, and go live – simple as that! What better way to engage with your audience than giving them a real glimpse of what you're doing and what your core values ​​are. Live streaming and video content will continue to push the boundaries, allowing brands to drop the corporate veil, connect human-to-human, and allow users to participate in brand storytelling in ways that enrich the customer experience. So, start embracing the digital conversation by incorporating live content streaming, visuals and videos!

3. Personalization
Everyone's special, or at least we all like to think we are. No matter what your status is on this, you have to get personal with your target audience – for starters, your website, emails and social media should. Start segmenting your content to reach different types of audience members based on their preferences, habits, etc. – because let's face it, if you keep treating them as one homogeneous group you are bound to lose out on the huge potential of your message. Start truly analyzing the data: location, age, needs, hobbies and so forth – the technology is available, so make the most of it and you will not lose out.

4. Purpose Driven Marketing
Become a brand that gives and gets! In today's world we're all looking to be part of something bigger, something meaningful that will make a difference. Everyone's passionate about their causes and trust me, customers will love that you have one too. Partner with a non-profit or charity, or set up an internal program that "gives back" in some way – and you're bound to win over the hearts of your customers as well as employees, helping them connect more fully with your brand As a whole.

5. Native Advertising
No one likes ads, unless you manage to slip them into content contacts that your users are already part of and give value to. This is the core reason native advertising is taking the marketing world by storm: $ 36.3 billion will be spent on native ad spending by 2021. Good native advertising is not meant to be trickery; It's certainly allowing a storyteller to share publishing tools with marketer, whilst at the same time maintain consumer trust by telling the truth, being transparent as to who's telling it, and finally adding value to the conversation with an audience. If done properly, it can be a win-win situation.

6. Mobile
Mobile is not just first, it's second, third – it's everywhere and everything! Internet traffic is firmly derived more from mobile devices than desks and if you're not geared to your content, ads and online experience towards mobile users, you are definitely missing a huge opportunity. Remember not to stop at optimizing for mobile. Also, ensure that the specific content is integrated and respectful of the lifestyles of users-on-the-go!

7. Embrace the lOT
How awesome is it that your fridge can actually remind you that you're running out of milk and gives you the option to place an order immediately! Everyday objects are beginning to connect to the internet, and this trend is going to open the doors for brands to play a more active part in the everyday lives of consumers. By 2020 there will be 75 billion connected devices – now that's a boom! The implications are huge and far ranging as we will witness a transformation in the way we live our lives, and consequently the way we market our brands.

In short, keep the 7 in mind, utilize your budgets effectively and stay ahead of the game



Source by Frosso Poly

Share Button

Top 2010 Fantasy Football Overvalued Players

Share Button

One of the keys to winning a fantasy football league is the ability to recognize overvalued players and to ignore them. "Slumpers" are NFL players who tend to be drawn in the top 3 at their position and produce like players drafted in double-digit rounds. These players are also known as "Draft Killers", especially if they are first or second round players. The key to winning your fantasy football league is to find players that will produce on a consistent basis. You may be able to offset one Slumper with a Sleeper, but it is better to just avoid the dead weight, if you can see any signs of a potential downfall. There are times that the signs are not present though. A perfect example of this from 2009 was Matt Forte. No one expected a drop of 300 yards and 8 total TDs from his rookie season of 2008. The 2009 Michael Turner drop-off was not a surprise since he logged 376 carries in 2008. Below is the top overvalued fantasy football players by position.

2010 Fantasy Football Slumpers

QB: Matt Schaub (Houston) – As temptation as it is put to Brett Favre in this position, he has not signed on with the Vikings for 2010, even though it is as inevitable as the sun rising. So, he must be omitted. Our choice for QB is Matt Schaub. He has been going as high as the third round in many of our drafts. There are too many quality RBs and WRs available at this point in the draft. Schaub is too fragile to spend a pick on him here. Somehow, he blamed the whole season in 2009, but it is foolhardy to expect that again in 2010. Plus, his success is largely tied to WR Andre Johnson. Johnson enters the 2010 season a bit miffed that the Texans have not torn up his current contract and rewarded him with a huge bonus and top WR cash. This situation tends to distract a player so Schaub will suffer if Johnson's head is in fully in the game.

RB: Steven Jackson (St. Louis) – There is no player in the NFL that I admire than SJax. He is on the worst team in the league and he is the only player that makes the Rams come close to resembling a professional football team. Yet, he does not complain about his contract or the lack of talent that surrounds him. He simply takes the ball and punishes defenders. However, continuously running into 8-man fronts takes its toll. It will remain that way this year since the Rams are breaking in a rookie QB. While Jackson did put up over 1400 yards last year, he did carry the ball 326 times, plus caught 51 passes. That is a lot of action and he only found the end zone on 4 carries. The last time he approached this much activity was 2006. In 2007, his yardage dropped by 33%, his TDs by 62% and his receptions by 42%. You could see the toll it took in 2009 as his final three games yielded a total of 184 yards, 7 receptions and zero TDs. Jackson is still being drawn in the first round. You can not risk your top pick running out of steam in your plays and not being able to sniff the end zone.

WR: Larry Fitzgerald (Arizona) – Fitz may be the most talented wide receiver in the NFL. However, he will be catching passes from one of the worst starting quarterbacks in the league; Matt Leinart. Leinart was the full-time starter in 2006 and it was the worst season of Fitzgerald's career (69/946/6). Last year, when Leinart started versus Tennessee, Fitz was targeted 5 times and caught a measly 4 passes for 34 yards and no TDs. With the dual running threat in Beanie Wells and Tim Hightower, I expect similar numbers to 2006 for Fitzgerald, which is definitely not worthy of your first or second draft pick.

TE: Greg Olsen (Chicago) – Olsen enjoyed his best season as a pro last year; Increasing his receptions, yards and TDs (jumping to 8). He has two issues working against him this year. First off, the Bears rented Mike Martz. Martz is known to forget that tight end is an actual off position. Many of his plays require quick reads and throws. While Olsen is one of the most athletic tight ends in the league, even he needs time to get open. The other issue is that Chicago found out that they actually have receivers on their roster. Devin Hester and Johnny Knox turned in remarkable numbers last year compared to their expectations and will thrive in Martz's offense this year. Even better, just when the league thought it had the Bears' passing scheme defended well (see Cutler's interceptions), along came Devin Aromashodu. In Aromashodu's (how fun is it to say "Aromashodu" ?!) last 4 games, he caught 22 passes for 282 yards and 4 TDs. These three receivers remember Martz of the trio he had in St. Louis. Louis. Can anyone name a Rams tight end during the early 2000s?

D: Pittsburgh Steelers – The Steel Curtain was a bit tarnished in 2009. They cave up 306 points and only generated 22 turnovers. You could contend that a lot of that was attributed to the defense missing Troy Polamalu. But, the fact remains that they are getting older and even a bit crotchety. LB LaMarr Woodley has repeatedly voiced his displeasure over his contract. During the 2009 season, they lacked their normal killer instinct; Losing games at the end to Chicago, Cincinnati, Kansas City and Oakland that they normally would not have in the past. Super Bowl hangover? Possibly, but I no longer see this defense as a top-5 defense.

K: Pick one (All) – Any kicker drafted before the last 2 rounds. In reality, the best way to evaluate a kicker is by his Bye week. Take one kicker and one kicker only and then pick one that is available with the latest Bye week so you can forget about that position for as long as possible.



Source by Bill E Parsons

Share Button

Top 2010 Fantasy Football Overvalued Players

Share Button

One of the keys to winning a fantasy football league is the ability to recognize overvalued players and to ignore them. "Slumpers" are NFL players who tend to be drawn in the top 3 at their position and produce like players drafted in double-digit rounds. These players are also known as "Draft Killers", especially if they are first or second round players. The key to winning your fantasy football league is to find players that will produce on a consistent basis. You may be able to offset one Slumper with a Sleeper, but it is better to just avoid the dead weight, if you can see any signs of a potential downfall. There are times that the signs are not present though. A perfect example of this from 2009 was Matt Forte. No one expected a drop of 300 yards and 8 total TDs from his rookie season of 2008. The 2009 Michael Turner drop-off was not a surprise since he logged 376 carries in 2008. Below is the top overvalued fantasy football players by position.

2010 Fantasy Football Slumpers

QB: Matt Schaub (Houston) – As temptation as it is put to Brett Favre in this position, he has not signed on with the Vikings for 2010, even though it is as inevitable as the sun rising. So, he must be omitted. Our choice for QB is Matt Schaub. He has been going as high as the third round in many of our drafts. There are too many quality RBs and WRs available at this point in the draft. Schaub is too fragile to spend a pick on him here. Somehow, he blamed the whole season in 2009, but it is foolhardy to expect that again in 2010. Plus, his success is largely tied to WR Andre Johnson. Johnson enters the 2010 season a bit miffed that the Texans have not torn up his current contract and rewarded him with a huge bonus and top WR cash. This situation tends to distract a player so Schaub will suffer if Johnson's head is in fully in the game.

RB: Steven Jackson (St. Louis) – There is no player in the NFL that I admire than SJax. He is on the worst team in the league and he is the only player that makes the Rams come close to resembling a professional football team. Yet, he does not complain about his contract or the lack of talent that surrounds him. He simply takes the ball and punishes defenders. However, continuously running into 8-man fronts takes its toll. It will remain that way this year since the Rams are breaking in a rookie QB. While Jackson did put up over 1400 yards last year, he did carry the ball 326 times, plus caught 51 passes. That is a lot of action and he only found the end zone on 4 carries. The last time he approached this much activity was 2006. In 2007, his yardage dropped by 33%, his TDs by 62% and his receptions by 42%. You could see the toll it took in 2009 as his final three games yielded a total of 184 yards, 7 receptions and zero TDs. Jackson is still being drawn in the first round. You can not risk your top pick running out of steam in your plays and not being able to sniff the end zone.

WR: Larry Fitzgerald (Arizona) – Fitz may be the most talented wide receiver in the NFL. However, he will be catching passes from one of the worst starting quarterbacks in the league; Matt Leinart. Leinart was the full-time starter in 2006 and it was the worst season of Fitzgerald's career (69/946/6). Last year, when Leinart started versus Tennessee, Fitz was targeted 5 times and caught a measly 4 passes for 34 yards and no TDs. With the dual running threat in Beanie Wells and Tim Hightower, I expect similar numbers to 2006 for Fitzgerald, which is definitely not worthy of your first or second draft pick.

TE: Greg Olsen (Chicago) – Olsen enjoyed his best season as a pro last year; Increasing his receptions, yards and TDs (jumping to 8). He has two issues working against him this year. First off, the Bears rented Mike Martz. Martz is known to forget that tight end is an actual off position. Many of his plays require quick reads and throws. While Olsen is one of the most athletic tight ends in the league, even he needs time to get open. The other issue is that Chicago found out that they actually have receivers on their roster. Devin Hester and Johnny Knox turned in remarkable numbers last year compared to their expectations and will thrive in Martz's offense this year. Even better, just when the league thought it had the Bears' passing scheme defended well (see Cutler's interceptions), along came Devin Aromashodu. In Aromashodu's (how fun is it to say "Aromashodu" ?!) last 4 games, he caught 22 passes for 282 yards and 4 TDs. These three receivers remember Martz of the trio he had in St. Louis. Louis. Can anyone name a Rams tight end during the early 2000s?

D: Pittsburgh Steelers – The Steel Curtain was a bit tarnished in 2009. They cave up 306 points and only generated 22 turnovers. You could contend that a lot of that was attributed to the defense missing Troy Polamalu. But, the fact remains that they are getting older and even a bit crotchety. LB LaMarr Woodley has repeatedly voiced his displeasure over his contract. During the 2009 season, they lacked their normal killer instinct; Losing games at the end to Chicago, Cincinnati, Kansas City and Oakland that they normally would not have in the past. Super Bowl hangover? Possibly, but I no longer see this defense as a top-5 defense.

K: Pick one (All) – Any kicker drafted before the last 2 rounds. In reality, the best way to evaluate a kicker is by his Bye week. Take one kicker and one kicker only and then pick one that is available with the latest Bye week so you can forget about that position for as long as possible.



Source by Bill E Parsons

Share Button

Pros and Cons of Gas Powered Airsoft Guns

Share Button

Priced somewhere between spring and electric powered guns, gas powered Airsoft guns can be used for single shot, semi-automatic or fully automatic operation. They tend to be used by collectors due to their very authentic look and feel in use, but serious gamers will tend to use electric Airsoft guns for regular use.

The most common gas used is a mixture of polysiloxane lubricant and propane known as ‘green gas’. Less commonly used are ‘red gas’, a chlorofluorocarbon that has been banned for use in the USA and many other countries due to its ozone-depleting properties, and compressed CO2, nitrogen or air. Compressed gases need high operating pressures that can tend to cause damage to the guns due to the pressures involved, particularly damage to the bolt and slide.

Gas Powered Airsoft Guns: Pros

A major advantage of gas guns over spring guns has already been stated: they can be used for semi- and fully automatic operation, whereas spring guns are limited to single shot use. This is because the spring has to be tensioned back after each individual shot.

An electric mechanism cannot be used in many pistols due to the size constraints imposed by their design. It is just not possible to manufacture an electric Airsoft pistol that replicates the genuine guns produced by many manufacturers. Those that collect true replicas will therefore tend to choose a gas-operated pistol rather than sacrifice authenticity.

Another benefit of a gas Airsoft gun is the ‘blowback’ mechanism. This mechanism is not available on all gas guns, and costs a bit extra, but if you want the authentic feel of a gun when firing then it’s worth the extra cost. With an Airsoft gas blowback gun, the slide moves back with each shot and gives you a recoil effect – just like in a real gun.

Many people choose gas as their preferred Airsoft automatic rifle because of this degree of realism – but make sure that the clip can hold a good number of bbs or you won’t be shooting on auto for very long! You can get blowback with other forms of Airsoft power, but gas is best and most gas guns are now fitted with it.

Gas guns offer more power and hence range than electric or spring powered Airsoft guns. Some offer a muzzle velocity of around 400 ft/sec, and this feature is best used in semi or fully automatic mode.

Gas Powered Airsoft Guns: Cons

The regulation and distribution of gas in an Airsoft gun means that gas guns are more complex mechanically than spring guns and electric guns, although are priced somewhere between the two. Some believe the simplicity of the spring guns in play make them more convenient, and when also taking cost into consideration, tend to prefer spring powered Airsoft guns to gas. Others prefer to go for electric or non-blowback gas guns for certain specialist uses such as target shooting.

There is a potential problem associated with liquefied gases such as green gas, in that the gas is very cold when in liquefied form. It can therefore cool down the mechanism of the gun in areas that are in contact with the liquid rather than its gaseous form, and this can slow down its firing rate and range. This is particularly so in automatic mode.

Not only that, but if the propellant is moved at high velocities through narrow apertures, it can freeze up and not only slow the gun down but also stop it altogether. Many believe this to be unlikely, but it can happen. You could use CO2, compressed nitrogen or air, but that can also damage the mechanism.

Blowback or Non-Blowback?

Many buy gas guns for their realism, but electric or spring powered Airsoft guns for play. A problem associated with using blowback with automatic firing in gaming is that it uses gas up quickly, and you may have to carry spare canisters around, slowing you up in the field. So many prefer not to use blowback or to use electric guns for play in auto mode.

Not many gas guns are now available without blowback, but most sniper rifles exclude the feature. That is because the extra gas needed for the slide or bolt operation reduces the potential range of the bb in a sniper rifle, and hence reduces accuracy over distance. So electric or non-blowback gas for sniping, electric or spring for gaming, and gas for authenticity.

Gas powered Airsoft guns offer a number of advantages and disadvantages, but when assessing their pros and cons it is likely best to consider your purpose for buying one and then decide which type best suits your needs. There are no doubts whatsoever that gas power offers a gun that looks and feels like the real thing in use, but that blowback reduces gas life, particularly in full automatic firing mode

When considering the pros and cons of gas powered Airsoft guns, keep all of that in mind, but if authenticity and versatility are your main considerations then gas wins every time.



Source by James T Hand

Share Button

NCAA Bracket Predictions – Time To Start Winning!

Share Button

If you would like to perform well with your March Madness bracket pool, there are a select few essential factors to think about. You MUST consider a team's momentum entering the ncaa tournament and how well teams did against the spread. A team's momentum can carry a ncaa team all the way into the ncaa brackets for final four. Take George Mason a few years ago for example, a NUMBER 11 SEED made it to the final four. Things like this are unheard of, but very possible in march madness. George Mason's glass slipper sure did fit in 2006 where this magical run took place. Many people never even heard of George Mason or did not know where they were even located until their magical run. Now they will go down in memories and the record book, and be known to all of sports as the Cinderellas that almost won the national championship. Your bracket for your ncaa basketball tournament may be all crossed out and marked if you follow the trend of 2007. 2007 was one of the only time in 23 years where there were not really any major upsets.

A team may have had an excellent run during the season, but when yet one player from the starting five is missing, this could change the entire team chemistry. Team chemistry is critical when you take in account high seeded teams contending in the ncaa basketball tournament. Please take note of any team missing one of their star player's; This is a critical component of your bracketology.

Make sure you check the March Madness previews on each team and check out some free ncaa basketball picks. If you do your research, you can stay away from choosing a team that only looked good on paper. If a team can not work together, it is going to spell disaster a mile away. Your basketball bracket pick by each round will suffer if you pick teams that lack chemistry. It is always clever to make sure how well a team is performing recently. For a team to do sound in the big game, it will need a great deal of momentum in order to go on to the final four. If a team is a number one seed and is struggling as of late, almost 90% of the time they will also struggle when they enter the tournament.

Sports college picks are the greatest picks online sports books have to offer. Some of the greatest sports books out there are my two most personal favorites: Sportsbook.com and BetJamaica.com. They offer a huge bonus for just signing up. A lot of the times they will 100% match whatever you deposit. Also, there are a great number of ways to cash out. Bank wire transfers are definitely by far the best. In 3-5 days, your money is in your bank account.

Whatever method you choose or whatever sports book you use to place your wagers on, I wish you all the best of luck. There is positively a way to devise a college sports picks system. All it takes is hard work and dedication. Once you give some hard work and dedication your profits from betting will start to roll in.



Source by Chris Grisham

Share Button

How You Can Learn To Control Your Premature Ejaculation

Share Button

The simple truth about premature ejaculation is, many men struggle with it and have no idea how to handle it. Some men are not even sure whether they do issues with this sexual dysfunction. So how can you access this problem and what's more, is it at all possible to control premature ejaculation?

When could you have considered a premature ejaculator?

There are some men that ejaculate the second they make penetration or just a couple of thrrust there after. This is certainly classed as PE. If you are a man that reaches climax within the first minute after penetration, this is a premature ejaculation. If you ejaculate after a few minutes, this is not a PE, you may just racing to the gate and this is down to self control and your mindset. If you are reaching your climax in a few minutes, you have enough time to take control of the situation and to prolong it, if you really want to. If you asked your partner whether you should slow down some, I am sure you know what her answer would be! However, all is not lost and it really is not hard to control premature ejaculation.

Talking about asking your partner, let us face it, she should take priority and you should hold back at least, until she has come to an orgasm or is close to it. I know that there are men out there that say they can not control premature ejaculation until their partner has come to climax. We would be talking roughly between 5 to 20 minutes for most women. That makes it easy to understand why a huge percentage of women are not happy in their sex life. This clearly does not mean that she has no feelings for him however, she is left alone with her emotions and fantasies and when this happens repeatedly, the situation can take a turn for the worst and have a massive effect on the relationship.

How can we control premature ejaculation and satisfy our partner?

Some men take to the pharmaceuticals and use pills, creams and sprays that can be purchased on the high street in drug stores and adult erotic shops. These desensitizing products most certainly do work however, they can be very expensive and they do not give you a long term solution to your problem. There is then another problem that arises when using these products. They work on the simple basis, in that they numb your genitals, stop you from getting aroused and reaching your climax to quick. You just will not have as much fun with sex as you did before and that having been said, would your partner really enjoy it?

As I mentioned earlier, a great way to work around your PE would be to concentrate entirely on your partner. Make sure she is sexually aroused and maybe even short before her orgasm before you even think of penetration. Use everything you have to your disposition, fingers, tongue and mouth and full body contact to get her aroused before you jump into the final act. It really is a mindset thing and if you really wish to please her above all and put yourself in second place, the 5 to 25 minutes most women need can be reduced drastically reduced. You can train to control premature ejaculation if you really want to know how!

Some men just want to penetrate and get into top gear before she even knows what happens. The penis is the last thing she needs to arousse her sexually. Plenty of foreplay and oral sex is a great way to start and if you stay aware of what's happening around you and build her sexual participation to the max, you will know when your time has come.

There are no problems, there are only solutions!

If you suffer from premature ejaculation and really want to take control of the situation, leave your penis out of play until the last minute. Satisfy your partner. Find out what she likes and wants. Take control of the situation with her in mind and at the last minute, you can race to the final goal. Premature Ejaculation is not as complicated as most men think and I kid you not, with a little effort on your part, it is possible to control premature ejaculation.



Source by Geoffrey Hadley

Share Button